smp_rep_phy_event - invoke REPORT PHY EVENT SMP function
smp_rep_phy_event [--desc] [--enumerate] [--help] [--hex] [--inter- face=PARAMS] [--long] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N]
SMP_REP_PHY_EVENT(8) SMP_UTILS SMP_REP_PHY_EVENT(8) NAME smp_rep_phy_event - invoke REPORT PHY EVENT SMP function SYNOPSIS smp_rep_phy_event [--desc] [--enumerate] [--help] [--hex] [--inter- face=PARAMS] [--long] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose] [--version] [--zero] SMP_DEVICE[,N] DESCRIPTION Sends a SAS Serial Management Protocol (SMP) REPORT PHY EVENT function request to an SMP target. The SMP target is identified by the SMP_DEVICE and the SAS_ADDR. Depending on the interface, the SAS_ADDR may be deduced from the SMP_DEVICE. The mpt interface uses SMP_DEVICE to identify a HBA (an SMP initiator) and needs the additional ,N to differentiate between HBAs if there are multiple present. Reports zero or more phy event descriptors. Each descriptor contains a phy event source, a phy event (i.e. a count) and a peak value detector theshold. At least one phy event should be maintained for each phy. OPTIONS Mandatory arguments to long options are mandatory for short options as well. -d, --desc precede each phy event descriptor with a line announcing its descriptor index number. Index numbers start at 1. -e, --enumerate enumerate all of the known Phy Event Source names, one per line preceded by its value in hex. Ignores SMP_DEVICE if it is given; most other options are also ignored. Exits after displaying the names. -h, --help output the usage message then exit. -H, --hex output the response (less the CRC field) in hexadecimal. -I, --interface=PARAMS interface specific parameters. In this case "interface" refers to the path through the operating system to the SMP initiator. See the smp_utils man page for more information. -l, --long prefix each phy event source string with its numeric identifier in hex. For example: "[0x1]: Invalid word count: 23" -p, --phy=ID phy identifier. ID is a value between 0 and 254. Default is 0. -r, --raw send the response (less the CRC field) to stdout in binary. All error messages are sent to stderr. -s, --sa=SAS_ADDR specifies the SAS address of the SMP target device. Typically this is an expander. This option may not be needed if the SMP_DEVICE has the target's SAS address within it. The SAS_ADDR is in decimal but most SAS addresses are shown in hexadecimal. To give a number in hexadecimal either prefix it with '0x' or put a trailing 'h' on it. -v, --verbose increase the verbosity of the output. Can be used multiple times -V, --version print the version string and then exit. ATTRIBUTES See attributes(7) for descriptions of the following attributes: +---------------+--------------------------+ |ATTRIBUTE TYPE | ATTRIBUTE VALUE | +---------------+--------------------------+ |Availability | system/storage/smp_utils | +---------------+--------------------------+ |Stability | Uncommitted | +---------------+--------------------------+ NOTES Similar information is maintained for SAS SSP target phys (e.g. on a SAS disk). It can be obtained from the Protocol Specific Port log page with the sg_logs utility. Similar information may be obtained for SAS initiator phys (e.g. on a SAS HBA). As an example in Linux 2.6.28 error information can be found in this directory /sys/class/sas_phy/phy-4:0 (for the phy 0 in SCSI/SAS host 4). Similar information may be obtained for SATA device phys (e.g. on a SATA disk). If there is a SAT layer between OS and the SATA device then the sg_sat_phy_event utility can fetch the information. Source code for open source software components in Oracle Solaris can be found at https://www.oracle.com/downloads/opensource/solaris-source- code-downloads.html. This software was built from source available at https://github.com/oracle/solaris-userland. The original community source was downloaded from http://sg.danny.cz/sg/p/smp_utils-0.98.tgz. Further information about this software can be found on the open source community website at http://sg.danny.cz/sg/smp_utils.html. CONFORMING TO The SMP REPORT PHY EVENT function was introduced in SAS-2 . AUTHORS Written by Douglas Gilbert. REPORTING BUGS Report bugs to <dgilbert at interlog dot com>. COPYRIGHT Copyright (C) 2011 Douglas Gilbert This software is distributed under a FreeBSD license. There is NO war- ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR- POSE. SEE ALSO smp_utils, smp_phy_control, smp_rep_phy_event_list(smp_utils) sg_logs, sg_sat_phy_event(sg3_utils) smp_utils-0.97 December 2011 SMP_REP_PHY_EVENT(8)