Go to main content

man pages section 1M: System Administration Commands

Exit Print View

Updated: July 2017
 
 

ripd (1m)

Name

ripd - a RIP routing engine for use with Quagga routing software.

Synopsis

ripd  [ -dhrv ] [ -f config-file ] [ -i pid-file ] [ -P port-number ] [
-A vty-address ] [ -u user ] [ -g group ]

Description

RIPD(1M)                        Version 0.97.3                        RIPD(1M)



NAME
       ripd - a RIP routing engine for use with Quagga routing software.

SYNOPSIS
       ripd  [ -dhrv ] [ -f config-file ] [ -i pid-file ] [ -P port-number ] [
       -A vty-address ] [ -u user ] [ -g group ]

DESCRIPTION
       ripd is a routing component that works with the Quagga routing engine.

OPTIONS
       Options available for the ripd command:

OPTIONS
       -d, --daemon
              Runs in daemon mode, forking and exiting from tty.

       -f, --config-file config-file
              Specifies the config file to use for startup. If  not  specified
              this option will likely default to /usr/local/etc/ripd.conf.

       -g, --group group
              Specify the group to run as. Default is quagga.

       -h, --help
              A brief message.

       -i, --pid_file pid-file
              When  ripd starts its process identifier is written to pid-file.
              The init system uses the recorded PID to stop or  restart  ripd.
              The likely default is /var/run/ripd.pid.

       -P, --vty_port port-number
              Specify the port that the ripd VTY will listen on. This defaults
              to 2602, as specified in /etc/services.

       -A, --vty_addr vty-address
              Specify the address that the ripd VTY will listen on. Default is
              all interfaces.

       -u, --user user
              Specify the user to run as. Default is quagga.

       -r, --retain
              When the program terminates, retain routes added by ripd.

       -v, --version
              Print the version and exit.

FILES
       /usr/local/sbin/ripd
              The default location of the ripd binary.

       /usr/local/etc/ripd.conf
              The default location of the ripd config file.

       $(PWD)/ripd.log
              If  the  ripd process is config'd to output logs to a file, then
              you will find this file in the directory where you started ripd.

WARNING
       This man page is intended to be a  quick  reference  for  command  line
       options. The definitive document is the Info file Quagga.

DIAGNOSTICS
       The  ripd  process may log to standard output, to a VTY, to a log file,
       or through syslog to the system  logs.  ripd  supports  many  debugging
       options, see the Info file, or the source for details.


ATTRIBUTES
       See attributes(5) for descriptions of the following attributes:


       +---------------+-------------------------------+
       |ATTRIBUTE TYPE |       ATTRIBUTE VALUE         |
       +---------------+-------------------------------+
       |Availability   | system/network/routing/quagga |
       +---------------+-------------------------------+
       |Stability      | Volatile                      |
       +---------------+-------------------------------+
SEE ALSO
       bgpd(1m),  ripngd(1m),  ospfd(1m),  ospf6d(1m),  isisd(1m),  zebra(1m),
       vtysh(1)

BUGS
       ripd eats bugs for breakfast. If you have food for the maintainers  try
       http://bugzilla.quagga.net

AUTHORS
       See http://www.zebra.org and http://www.quagga.net or the Info file for
       an accurate list of authors.



NOTES
       This    software    was    built    from    source     available     at
       https://java.net/projects/solaris-userland.    The  original  community
       source     was     downloaded     from      http://www.quagga.net/down-
       load/quagga-0.99.19.tar.gz

       Further information about this software can be found on the open source
       community website at http://www.quagga.net/.



Quagga RIP daemon              25 November 2004                       RIPD(1M)