Table of Contents
- List of Figures
- List of Tables
- Title and Copyright Information
- Preface
- 1 About the SL150 Library
-
2
Install the Library
- Verify the Site Meets Environmental Requirements
- Prepare the Rack
- Unpack and Acclimate the Library
- Install the Base Module
-
Install the Expansion Module
- Unpack the Expansion Module Accessory Kit
- Remove the Library Floor
- Install Clip Nuts for the Expansion Module (for square hole racks only)
- Prepare the Expansion Module by Removing the Cartridge Magazines
- Install the Floor in the Bottom Expansion Module
- Mount the Expansion Module
- Install the Rear Rails for the Expansion Module
- Secure the Expansion Module to the Rack Front
- Replace the Cartridge Magazines
- Label the Modules
- Install the Hook and Loop Strap
- Install Power Supplies and Tape Drives
- Cable the Library
- Unlock the Robot
- Apply Power to the Library
-
Configure the Library After Powering-on for the First Time
- Configure the Library: Login with the Default Admin
- Configure the Library Step 1 of 6: Change the Default Administrator Password
- Configure the Library Step 2 of 6: Configure the Network Port 1
- Configure the Library Step 3 of 6: Set the Library Date and Time
- Configure the Library Step 4 of 6: Set the Drive Element Addressing Mode
- Configure the Library Step 5 of 6: Configure the Mailslot, Reserved Slots and Volume Label Format
- Configure the Library Step 6 of 6: Review and Apply Initialization Settings
- Configure the Library: Finish the New Configuration
- Run a Self-Test
- 3 Basic User Interface Operations
-
4
Configure the Library
- Run the Configuration Wizard
- Update Firmware
- Manage the Library's SSL/TLS Certificate for HTTPS
- Configure Accessibility Settings
- Set Automatic Screen Refresh
- 5 Users
-
6
Tape Cartridges (Media)
- Library Support of LTO9 Tape Calibration
- Media Labels
- View a List of Tape Cartridges
- View Tape Cartridge Health (Media Health)
- Guidelines for Handling Tape Cartridges
- Load the Magazines (Bulk Loading)
- Import or Export Cartridges Using the Mailslot
- Move Tape Cartridges with the Remote Interface
- Determine the Required Number of Reserved System Slots
- Determine the Number of Cleaning Cartridges
- Manage Expired Cleaning Cartridges
-
Media Validation
- Add a Drive to the Media Validation Pool
- Remove a Drive from the Media Validation Pool
- Start a Media Validation
- Manually Cancel a Validation in Progress
- Clear a Media Validation Drive Reservation
- Monitor Media Validation
- Media Validation Types
- Effects of a Library Restart on Media Validation
- Why Aren't the Media Validation Drives Showing in STA?
-
7
Tape Drives
- Supported Tape Drives
- Bridged Tape Drives
- Library Managed Encryption (LME)
- View Drive Information
-
Configure Drive Cleaning
- Enable Library-Managed Drive Auto Cleaning
-
Configure Host-Managed Drive Cleaning
- Configure Automatic Cleaning in Oracle Secure Backup During Drive Setup
- Set Up Auto Cleaning with FUJIFILM Object Archive
- Set Up NetBackup for Reactive Cleaning
- Set Up Symantec Backup Exec Drive Cleaning
- Set Up Reactive Cleaning for HP StorageWorks Enterprise Backup Solution with HP Data Protector
- Set Up As-Needed Cleaning in IBM Tivoli Storage Manager (TSM)
- Set Up Tape-Alert Cleaning in EMC Networker
- Set Up CommVault Drive Cleaning
- Manually Clean a Drive (Not Recommended)
- Restart a Drive
- Enable or Disable Drive Ports
- Update the Drive Firmware
- 8 Monitor the Library
-
9
Service the Library
- Place the Library Online or Offline
- Power On the Library
- Power Off the Library
- Restart the Library
- Audit the Library
- Move the Library Rack
- Enable the Locate Light
-
Troubleshoot the Library
- Diagnose a Browser-Based User Interface Problem
-
Diagnose a Library Problem
- Diagnose Why You Cannot Login to the Remote Interface
- Use the Health Table to Diagnose the Issue
- Check if a Fault is Closed in the Health Log
- Locate and Remove a Cartridge Stuck in a Magazine Slot
- Locate and Clear Obstructions, Such as Loose or Protruding Cartridges
- Save the Health Log to a File
- Run a Self-Test
- Restore the Factory Default Configuration
- SAS-2 and SAS-3 Configuration Issues
- Get Parts and Technical Support
- Run a Self-Test
-
10
Replace Components (CRUs & FRUs)
- CRU Locations
- Drive Tray Removal and Replacement
- Power Supply Removal and Replacement
- Front Control Panel Removal and Replacement
- Module Controller Removal and Replacement
- Robot Module Removal and Replacement
- Expansion Module Chassis Removal and Replacement (FRU)
- Base Module Chassis Removal and Replacement (FRU)
- Validate the Component Installation
- Return CRU Components to Oracle
- Lock the Robot for Shipment within a Rack
- A Slot Mapping and Cartridge Locations
- Glossary
- Index