sg_rep_zones - send SCSI REPORT ZONES command
sg_rep_zones [--help] [--hex] [--maxlen=LEN] [--raw] [--readonly] [--report=OPT] [--start=LBA] [--verbose] [--version] DEVICE
SG_REP_ZONES(8) SG3_UTILS SG_REP_ZONES(8)
NAME
sg_rep_zones - send SCSI REPORT ZONES command
SYNOPSIS
sg_rep_zones [--help] [--hex] [--maxlen=LEN] [--raw] [--readonly]
[--report=OPT] [--start=LBA] [--verbose] [--version] DEVICE
DESCRIPTION
Sends a SCSI REPORT ZONES command to DEVICE and outputs the data
returned. This command is found in the ZBC draft standard, revision 4c
(zbc-r04c.pdf).
OPTIONS
Arguments to long options are mandatory for short options as well.
-h, --help
output the usage message then exit.
-H, --hex
output the response in hexadecimal to stdout. When used once the
whole response is output in ASCII hexadecimal with a leading
address (starting at 0) on each line. When used twice each zone
descriptor in the response is output separately in hexadecimal.
When used thrice the whole response is output in hexadecimal
with no leading address (on each line).
-m, --maxlen=LEN
where LEN is the (maximum) response length in bytes. It is
placed in the cdb's "allocation length" field. If not given (or
LEN is zero) then 8192 is used. The maximum allowed value of LEN
is 1048576.
-p, --partial
set the PARTIAL bit in the cdb.
-r, --raw
output the SCSI response (i.e. the data-out buffer) in binary
(to stdout).
-R, --readonly
open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag).
The default is to open it read-write.
-o, --report=OPT
where OPT will become the contents of the REPORTING OPTION field
in the cdb. The default value is 0 which means report a list of
all zones. Some other values are 1 for list zones with a zone
condition of empty; 2 for list zones with a zone condition of
implicitly opened; 3 for list zones with a zone condition of
explicitly opened; 4 for list zones with a zone condition of
closed; 5 for list zones with a zone condition of full; 6 for
list zones with a zone condition of read only; 7 for list zones
with a zone condition of offline. Other values are 0x10 for list
zones with RWP recommended set to true; 0x11 for list zones with
non-sequential write resource active set to true and 0x3f for
list zones with a zone condition of not write pointer.
-s, --start=LBA
where LBA is at the start or within the first zone to be
reported. The default value is 0. If LBA is not a zone start LBA
then the preceding zone start LBA is used for reporting. Assumed
to be in decimal unless prefixed with '0x' or has a trailing 'h'
which indicate hexadecimal.
-v, --verbose
increase the level of verbosity, (i.e. debug output).
-V, --version
print the version string and then exit.
EXIT STATUS
The exit status of sg_rep_zones is 0 when it is successful. Otherwise
see the sg3_utils(8) man page.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright (C) 2014-2016 Douglas Gilbert
This software is distributed under a FreeBSD license. There is NO war-
ranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
POSE.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
+---------------+--------------------------+
|ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+---------------+--------------------------+
|Availability | system/storage/sg3_utils |
+---------------+--------------------------+
|Stability | Pass-through uncommitted |
+---------------+--------------------------+
SEE ALSO
sg_reset_wp,sg_zone(sg3_utils)
NOTES
This software was built from source available at
https://github.com/oracle/solaris-userland. The original community
source was downloaded from http://sg.danny.cz/sg/p/sg3_utils-1.42.tgz
Further information about this software can be found on the open source
community website at http://sg.danny.cz/sg/sg3_utils.html.
sg3_utils-1.42 February 2016 SG_REP_ZONES(8)