qperf - Measure RDMA and IP performance
qperf qperf SERVERNODE [OPTIONS] TESTS
QPERF(1) User Commands QPERF(1)
NAME
qperf - Measure RDMA and IP performance
SYNOPSIS
qperf
qperf SERVERNODE [OPTIONS] TESTS
DESCRIPTION
qperf measures bandwidth and latency between two nodes. It can work
over TCP/IP as well as the RDMA transports. On one of the nodes, qperf
is typically run with no arguments designating it the server node. One
may then run qperf on a client node to obtain measurements such as
bandwidth, latency and cpu utilization.
In its most basic form, qperf is run on one node in server mode by
invoking it with no arguments. On the other node, it is run with two
arguments: the name of the server node followed by the name of the
test. A list of tests can be found in the section, TESTS. A variety
of options may also be specified.
One can get more detailed information on qperf by using the --help
option. Below are examples of using the --help option:
qperf --help examples Some examples of using qperf
qperf --help opts Summary of options
qperf --help options Description of options
qperf --help tests Short summary and description of tests
qperf --help TESTNAME More information on test TESTNAME
EXAMPLES
In these examples, we first run qperf on a node called myserver in
server mode by invoking it with no arguments. In all the subsequent
examples, we run qperf on another node and connect to the server which
we assume has a hostname of myserver.
To run a TCP bandwidth and latency test:
qperf myserver tcp_bw tcp_lat
To run a SDP bandwidth test for 10 seconds:
qperf myserver -t 10 sdp_bw
To run a UDP latency test and then cause the server to terminate:
qperf myserver udp_lat quit
To measure the RDMA UD latency and bandwidth:
qperf myserver ud_lat ud_bw
To measure RDMA UC bi-directional bandwidth:
qperf myserver rc_bi_bw
To get a range of TCP latencies with a message size from 1 to 64K
qperf myserver -oo msg_size:1:64K:*2 -vu tcp_lat
OPTIONS
-ar, --access_recv OnOff
If OnOff is non-zero, data is accessed once received. Other-
wise, data is ignored. By default, OnOff is 0. This can help
to mimic some applications.
-ar1 Cause received data to be accessed.
-ap, --alt_port Port
Set alternate path port. This enables automatic path failover.
-lap, --loc_alt_port Port
Set local alternate path port. This enables automatic path
failover.
-rap, --rem_alt_port Port
Set remote alternate path port. This enables automatic path
failover.
-ca, --cpu_affinity PN
Set cpu affinity to PN. CPUs are numbered sequentially from 0.
If PN is "any", any cpu is allowed otherwise the cpu is limited
to the one specified.
-lca, --loc_cpu_affinity PN
Set local processor affinity to PN.
-rca, --rem_cpu_affinity PN
Set remote processor affinity to PN.
-f, --flip OnOff
If non-zero, cause sender and receiver to play opposite roles.
-f1 Cause sender and receiver to play opposite roles.
-h, --help Topic
Print out information about Topic. To see the list of topics,
type qperf --help
-H, --host Host
Run test between the current node and the qperf running on node
Host. This can also be specified as the first non-option argu-
ment.
-i, --id Device:Port
Use RDMA Device and Port.
-li, --loc_id Device:Port
Use local RDMA Device and Port.
-ri, --rem_id Device:Port
Use remote RDMA Device and Port.
-lp, --listen_port Port
Set the port we listen on to ListenPort. This must be set to
the same port on both the server and client machines. The
default value is 19765.
-oo, --loop Var:Init:Last:Incr
Run a test multiple times sequencing through a series of values.
Var is the loop variable; Init is the initial value; Last is the
value it must not exceed and Incr is the increment. It is use-
ful to set the --verbose_used (-vu) option in conjunction with
this option.
-m, --msg_size Size
Set the message size to Size. The default value varies by test.
It is assumed that the value is specified in bytes however, a
trailing kib or K, mib or M, or gib or G indicates that the size
is being specified in kibibytes, mebibytes or gibibytes respec-
tively while a trailing kb or k, mb or m, or gb or g indicates
kilobytes, megabytes or gigabytes respectively.
-mt, --mtu_size Size
Set the MTU size. Only relevant to the RDMA UC/RC tests. Units
are specified in the same manner as the --msg_size option.
-n, --no_msgs N
Set test duration by number of messages sent instead of time.
-cp, --cq_poll OnOff
Turn polling mode on or off. This is only relevant to the RDMA
tests and determines whether they poll or wait on the completion
queues. If OnOff is 0, they wait; otherwise they poll.
-lcp, --loc_cq_poll OnOff
Locally turn polling mode on or off.
-rcp, --rem_cq_poll OnOff
Remotely turn polling mode on or off.
-cp1 Turn polling mode on.
-lcp1 Turn local polling mode on.
-rcp1 Turn remote polling mode on.
-ip, --ip_port Port
Use Port to run the socket tests. This is different from --lis-
ten_port which is used for synchronization. This is only rele-
vant for the socket tests and refers to the TCP/UDP/SDP/RDS/SCTP
port that the test is run on.
-e, --precision Digits
Set the number of significant digits that are used to report
results.
-nr, --rd_atomic Max
Set the number of in-flight operations that can be handled for a
RDMA read or atomic operation to Max. This is only relevant to
the RDMA Read and Atomic tests.
-lnr, --loc_rd_atomic Max
Set local read/atomic count.
-rnr, --rem_rd_atomic Max
Set remote read/atomic count.
-sl, --service_level SL
Set RDMA service level to SL. This is only used by the RDMA
tests. The service level must be between 0 and 15. The default
service level is 0.
-lsl, --loc_service_level SL
Set local service level.
-rsl, --rem_service_level SL
Set remote service level.
-sb, --sock_buf_size Size
Set the socket buffer size. This is only relevant to the socket
tests.
-lsb, --loc_sock_buf_size Size
Set local socket buffer size.
-rsb, --rem_sock_buf_size Size
Set remote socket buffer size.
-sp, --src_path_bits N
Set source path bits. If the LMC is not zero, this will cause
the connection to use a LID with the low order LMC bits set to
N.
-lsp, --loc_src_path_bits N
Set local source path bits.
-rsp, --rem_src_path_bits N
Set remote source path bits.
-sr, --static_rate Rate
Force InfiniBand static rate. Rate can be one of: 2.5, 5, 10,
20, 30, 40, 60, 80, 120, 1xSDR (2.5 Gbps), 1xDDR (5 Gbps), 1xQDR
(10 Gbps), 4xSDR (2.5 Gbps), 4xDDR (5 Gbps), 4xQDR (10 Gbps),
8xSDR (2.5 Gbps), 8xDDR (5 Gbps), 8xQDR (10 Gbps).
-lsr, --loc_static_rate
Force local InfiniBand static rate
-rsr, --rem_static_rate
Force remote InfiniBand static rate
-t, --time Time
Set test duration to Time. Specified in seconds however a
trailing m, h or d indicates that the time is specified in min-
utes, hours or days respectively.
-to, --timeout Time
Set timeout to Time. This is the timeout used for various
things such as exchanging messages. The default is 5 seconds.
-lto, --loc_timeout Time
Set local timeout to Time. This may be used on the server to
set the timeout when initially exchanging data with each client.
However, as soon as we receive the client's parameters, the
client's remote timeout will override this parameter.
-rto, --rem_timeout Time
Set remote timeout to Time.
-un, --unify_nodes
Unify the nodes. Describe them in terms of local and remote
rather than send and receive.
-uu, --unify_units
Unify the units that results are shown in. Uses the lowest com-
mon denominator. Helpful for scripts.
-ub, --use_bits_per_sec
Use bits/sec rather than bytes/sec when displaying networking
speed.
-cm, --use_cm OnOff
Use the RDMA Connection Manager (CM) if OnOff is non-zero. It
is necessary to use the CM for iWARP devices. The default is to
establish the connection without using the CM. This only works
for the tests that use the RC transport.
-cm1 Use RDMA Connection Manager.
-v, --verbose
Provide more detailed output. Turns on -vc, -vs, -vt and -vu.
-vc, --verbose_conf
Provide information on configuration.
-vs, --verbose_stat
Provide information on statistics.
-vt, --verbose_time
Provide information on timing.
-vu, --verbose_used
Provide information on parameters used.
-vv, --verbose_more
Provide even more detailed output. Turns on -vvc, -vvs, -vvt
and -vvu.
-vvc, --verbose_more_conf
Provide more information on configuration.
-vvs, --verbose_more_stat
Provide more information on statistics.
-vvt, --verbose_more_time
Provide more information on timing.
-vvu, --verbose_more_used
Provide more information on parameters used.
-V, --version
The current version of qperf is printed.
-ws, --wait_server Time
If the server is not ready, continue to try connecting for Time
seconds before giving up. The default is 5 seconds.
TESTS
conf Show configuration
quit Cause the server to quit
rds_bw RDS streaming one way bandwidth
rds_lat
RDS one way latency
sctp_bw
SCTP streaming one way bandwidth
sctp_lat
SCTP one way latency
sdp_bw SDP streaming one way bandwidth
sdp_lat
SDP one way latency
tcp_bw TCP streaming one way bandwidth
tcp_lat
TCP one way latency
udp_bw UDP streaming one way bandwidth
udp_lat
UDP one way latency
rc_bi_bw
RC streaming two way bandwidth
rc_bw RC streaming one way bandwidth
rc_lat RC one way latency
uc_bi_bw
UC streaming two way bandwidth
uc_bw UC streaming one way bandwidth
uc_lat UC one way latency
ud_bi_bw
UD streaming two way bandwidth
ud_bw UD streaming one way bandwidth
ud_lat UD one way latency
xrc_bi_bw
XRC streaming two way bandwidth
xrc_bw XRC streaming one way bandwidth
xrc_lat
XRC one way latency
rc_rdma_read_bw
RC RDMA read streaming one way bandwidth
rc_rdma_read_lat
RC RDMA read one way latency
rc_rdma_write_bw
RC RDMA write streaming one way bandwidth
rc_rdma_write_lat
RC RDMA write one way latency
rc_rdma_write_poll_lat
RC RDMA write one way polling latency
uc_rdma_write_bw
UC RDMA write streaming one way bandwidth
uc_rdma_write_lat
UC RDMA write one way latency
uc_rdma_write_poll_lat
UC RDMA write one way polling latency
rc_compare_swap_mr
RC compare and swap messaging rate
rc_fetch_add_mr
RC fetch and add messaging rate
ver_rc_compare_swap
Verify RC compare and swap
ver_rc_fetch_add
Verify RC fetch and add
AUTHOR
Written by Johann George.
BUGS
None of the RDMA tests are available if qperf is compiled without the
RDMA libraries. None of the XRC tests are available if qperf is com-
piled without the XRC extensions. The -f option is not yet implemented
in many of the tests.
ATTRIBUTES
See attributes(7) for descriptions of the following attributes:
+---------------+-----------------------+
|ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+---------------+-----------------------+
|Availability | network/open-fabrics |
+---------------+-----------------------+
|Stability | Pass-through volatile |
+---------------+-----------------------+
NOTES
This software was built from source available at
https://github.com/oracle/solaris-userland. The original community
source was downloaded from ['https://www.openfabrics.org/down-
loads/ibutils/ibutils-1.5.7-0.2.gbd7e502.tar.gz', 'https://www.openfab-
rics.org/downloads/libibverbs/libibverbs-1.1.8.tar.gz',
'https://www.openfabrics.org/downloads/libmlx4/libmlx4-1.0.6.tar.gz',
'https://www.openfabrics.org/downloads/libsdp/lib-
sdp-1.1.108-0.15.gd7fdb72.tar.gz', 'https://www.openfabrics.org/down-
loads/management/infiniband-diags-1.6.5.tar.gz', 'https://www.openfab-
rics.org/downloads/management/libibmad-1.3.12.tar.gz',
'https://www.openfabrics.org/downloads/management/libibu-
mad-1.3.10.2.tar.gz', 'https://www.openfabrics.org/downloads/manage-
ment/opensm-3.3.19.tar.gz', 'https://www.openfabrics.org/down-
loads/perftest/perftest-1.3.0-0.42.gf350d3d.tar.gz', 'https://www.open-
fabrics.org/downloads/qperf/qperf-0.4.9.tar.gz', 'https://www.openfab-
rics.org/downloads/rdmacm/librdmacm-1.0.21.tar.gz', 'https://www.open-
fabrics.org/downloads/rds-tools/rds-tools-2.0.4.tar.gz']
Further information about this software can be found on the open source
community website at http://www.openfabrics.org/.
qperf November 2012 QPERF(1)