Launch the Oracle ILOM Storage
Redirection CLI and Redirect Storage Devices
Use the following procedure to launch and use
the Oracle ILOM Storage Redirection CLI console:
Before You Begin
To launch the Storage Redirection CLI and redirect storage
devices, perform these steps:
- To
start the storage redirection service, perform one of the following:
- Run the storage
redirection service from the Oracle ILOM web interface as follows:
- In the Oracle ILOM
web interface, click Remote Control > Redirection > Launch Service.
The Opening Jnlpgenerator-cli file dialog box appears.
- In the Opening Jnlpgenerator-cli
dialog box, click “Open it with,” choose the javaws
(default) 32-bit JDK file, and then click OK.
- In the Security Warning dialog
box, click Run to start the storage redirection service.
- Open a command window or terminal
on the local client system to launch the Oracle ILOM Storage Redirection
CLI.
For Oracle ILOM Storage Redirection CLI launching instructions,
see Step 2.
- Start the (installed) storage
redirection service from a command window as follows:
- Open a command window
or terminal on the local client system.
For example:
Windows systems: From
the Start menu, click Run, type cmd, and
then click OK.
Oracle Solaris or Linux systems:
Open a terminal window on the desktop.
- Navigate to the location where
the Jnlpgenerator-cli file is installed, and
then issue the javaws rconsole.jnlp command to
start the service.
For example:
cd jnlp_file_location/javaws rconsole.jnlp
- To launch the Storage Redirection
CLI console from the command window or terminal, perform one of
the following procedures based on the shell mode being used:
|
|
Interactive shell mode |
The interactive mode is
useful when you need to enter a series of Storage Redirection commands.
To launch the Storage Redirection CLI using an interactive
shell mode, perform these steps:
In the command-line
interface, navigate to the directory where the storage redirection
client (StorageRedir.jar) is installed using
the cd command.
For example:
cd my_settings/storage_redirect_directory Enter the following command to launch the Storage
Redirection CLI:
java -jar StorageRedir.jar
For example:
C:\Documents and Settings\redirectstorage java -jar StorageRedir.jar
The <storageredir> prompt appears.
Note - If you are using Windows, you must specify an uppercase
letter for the target disk drive. For example, if the letter assigned
to the target disk drive was c: you must specify C: instead
of c:. Tip - Enter only one space before java and
one space before and after -jar. Otherwise, the java -jar StorageRedir.jar command
will fail. Related Information:
|
Non-interactive shell mode |
The non-interactive mode is useful when
you need to run a batch procedure or script.
To launch the Storage Redirection CLI console using an non-interactive
shell mode, perform these steps:
In the command-line
interface, enter the command to launch the Storage Redirection CLI
(java -jar StorageRedir.jar) at the shell prompt
($).
For example:
$ java -jar StorageRedir.jar
Note – If you
do not have a JAVA_HOME environment configured,
you might need to use the full path to your Java binary. For example,
if your JDK package was installed under /home/user_name/jdk,
then you would type:/home/user_name/jdk/bin/java -jar ... If the Storage Redirection CLI fails to launch,
a detailed error message appears explaining the error condition.
Otherwise, the Storage Redirection CLI is ready for user input.
Note - You can launch multiple Storage Redirection CLI consoles
by issuing the storage redirection command (-jar StorageRedir.jar)
from a local command window or terminal. Tip - Enter only one space before and after -jar.
Otherwise, the java -jar StorageRedir.jar command
will fail. Related Information:
|
|
- To verify that the storage redirection
service is running, type the following command:
test-service
A message appears stating whether the redirection service
passed or failed.
For command descriptions and shell mode syntax, see these
topics:
- To start storage redirection,
type the following start command followed by
the sub-commands and properties for the redirection device type,
path to device, remote SP user name and password, and the IP address
of the remote SP.
For example:
Note - Commands shown in the following example should be entered
as one continuous string.
start -r redir_type -t redir_type_path -u remote_username [-s remote_user_password] [-p non_default_storageredir_port] remote_SP_IP
For command descriptions and shell mode syntax, see these
topics:
- To view active storage redirection,
type the list command followed by the sub-commands
and properties for any non-default storage redirection ports and the
IP addresses of the remote host server SP.
For example:
list [-p non_default _storageredir_port] remote_SP
For command descriptions and shell mode syntax, see these
topics:
- To stop the redirection of a
storage device, type the stop command followed
by the commands and properties for the storage device type, remote
SP user name and password, storage redirection port, and IP address
of the remote host server SP.
For example:
stop -r redir_type -u
remote_username [-s
remote_user_password] [-p
non_defult_storageredir_port]
[-a yes/no]
remote_SP
For command descriptions and shell mode syntax, see these
topics:
- To display command-line Help,
type the following command:
help
The following information about the command syntax and usage
appears.
Usage: |
list
[-p storageredir_port] [remote_SP] start -r redir_type -t redir_type_path -u remote_username [-s
remote_user_password][-a yes/no][-p
storageredir_port] remote_SP stop -r redir_type -u
remote_username [-s remote_user_password] [-a
yes/no] [-p storageredir_port]
remote_SP stop-service [-p storageredir_port] test-service [-p storageredir_port] help version quit
|
|