sg_turs
(1m)
名前
sg_turs - send one or more SCSI TEST UNIT READY commands
形式
sg_turs [--help] [--number=NUM] [--progress] [--time]
[--verbose] [--version] DEVICE
sg_turs [-n=NUM] [-p] [-t] [-v] [-V] DEVICE
説明
SG3_UTILS SG_TURS(8)
NAME
sg_turs - send one or more SCSI TEST UNIT READY commands
SYNOPSIS
sg_turs [--help] [--number=NUM] [--progress] [--time]
[--verbose] [--version] DEVICE
sg_turs [-n=NUM] [-p] [-t] [-v] [-V] DEVICE
DESCRIPTION
This utility sends one or more SCSI TEST UNIT READY commands
to the DEVICE. This may be useful for timing the per command
overhead. Note that TEST UNIT READY has no associated data,
just a 6 byte command and a returned SCSI status value.
This utility supports two command line syntaxes, the pre-
ferred one is shown first in the synopsis and explained in
this section. A later section on the old command line syntax
outlines the second group of options.
OPTIONS
Arguments to long options are mandatory for short options as
well.
-h, --help
print out the usage message then exit.
-n, --number=NUM
performs TEST UNIT READY NUM times. If not given
defaults to 1. These suffix multipliers are permitted:
c C *1; w W *2; b B *512; k K KiB *1,024; KB *1,000; m
M MiB *1,048,576; MB *1,000,000; g G GiB
*1,073,741,824; and GB *1,000,000,000 . Also a suffix
of the form "x<n>" multiplies the leading number by
<n>. Alternatively a hex number may be given, prefixed
by either '0x' or has a trailing 'h'.
-O, --old
switch to older style options.
-p, --progress
show progress indication (a percentage) if available.
If --number=NUM is given, NUM is greater than 1 and an
initial progress indication was detected then this
utility waits 30 seconds before subsequent checks.
Exits when NUM is reached or there are no more progress
indications. Ignores --time option. See NOTES section
below.
-t, --time
after completing the requested number of TEST UNIT
READY commands, outputs the total duration and the
sg3_utils-1.30 Last change: August 2010 1
SG3_UTILS SG_TURS(8)
average number of commands executed per second.
-v, --verbose
increase level or verbosity.
-V, --version
print version string then exit.
ATTRIBUTES
See attributes(5) for descriptions of the following
attributes:
+---------------+--------------------------+
|ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+---------------+--------------------------+
|Availability | system/storage/sg3_utils |
+---------------+--------------------------+
|Stability | Uncommitted |
+---------------+--------------------------+
NOTES
The progress indication is optionally part of the sense
data. When a prior command that takes a long time to com-
plete (and typically precludes other media access commands)
is still underway, the progress indication can be used to
determine how long before the device returns to its normal
state.
The SCSI FORMAT command for disks used with the IMMED bit
set is an example of an operation that takes a significant
amount of time and precludes other media access during that
time. The IMMED bit set instructs the FORMAT command to
return control to the application client once the format has
commenced (see SBC-3). Several long duration SCSI commands
associated with tape drives also use the progress indication
(see SSC-3).
Early standards suggested that the SCSI TEST UNIT READY com-
mand be used for polling the progress indication. More
recent standards seem to suggest the SCSI REQUEST SENSE com-
mand should be used instead.
EXIT STATUS
The exit status of sg_turs is 0 when it is successful (e.g.
in the case of a mechanical disk, it is spun up and ready to
accept commands). For this utility the other exit status of
interest is 2 corresponding to the "not ready" sense key.
For other exit status values see the sg3_utils(8) man page.
OLDER COMMAND LINE OPTIONS
The options in this section were the only ones available
prior to sg3_utils version 1.23 . In sg3_utils version 1.23
sg3_utils-1.30 Last change: August 2010 2
SG3_UTILS SG_TURS(8)
and later these older options can be selected by either set-
ting the SG3_UTILS_OLD_OPTS environment variable or using
'--old' (or '-O) as the first option.
-n=NUM
performs TEST UNIT READY NUM times. If not given
defaults to 1. Equivalent to --number=NUM in the main
description.
-N switch to the newer style options.
-p show progress indication (a percentage) if available.
Equivalent to --progress in the main description.
-t after completing the requested number of TEST UNIT
READY commands, outputs the total duration and the
average number of commands executed per second. Equiv-
alent to --time in the main description.
-v increase level of verbosity.
-V print out version string then exit.
AUTHORS
Written by D. Gilbert
COPYRIGHT
Copyright (C) 2000-2008 Douglas Gilbert
This software is distributed under the GPL version 2. There
is NO warranty; not even for MERCHANTABILITY or FITNESS FOR
A PARTICULAR PURPOSE.
SEE ALSO
sg_inq, sg_request (sg3_utils)
This software was built from source available at
https://java.net/projects/solaris-userland. The original
community source was downloaded from
http://sg.danny.cz/sg/p/sg3_utils-1.33.tgz
Further information about this software can be found on the
open source community website at
http://sg.danny.cz/sg/sg3_utils.html.
sg3_utils-1.30 Last change: August 2010 3